News From G Instruments pH, REDOX / ORP, Dissolved Oxygen, mV, thermocouples Our new line of RS485 MODBUS RTU transmitters is a special design for pH, REDOX / ORP, dissolved oxygen mV and thermocouple signals. GpH140-11 has two inputs with an extremely high impedance, specially designed to measure pH and / or REDOX / ORP. GpH140-12 has one input for pH / REDOX / ORP and one for mV / thermocouples. GpH140-22 has two inputs for mV / thermocouples. All of them have as a standard one Pt1000 RTD input, the built-in cold junction compensation and one 4-20 mA two wire loop power input. Flow Computers For Irrigation Our new line of flow computers is a special design for irrigation. All of them measure accurately and display flow rate with input pulses down to one pulse every 5 minutes. New Line Of Panel Mount Flow Computers All GFC100/200 series flow computers / totalizers now have a panel mount version in DIN 72x72 mm with IP65 (NEMA-4) protection. GMAG100 improvements A new version of GMAG100 has been released. Now it has larger range of baud rates and programmable stop bits. GFC111-MB and AH111-MB GFC111-MB and AH111-MB Now they have up to 5 programmable decimal places, total up to 9 digits (1 billion), larger ranges of baud rates, programmable stop bits and other improvements. GFCP111-MB and AHP111-MB - the panel mount versions, have been released. Conductivity Transmitters GCT20K and GCT20K-MB now have a programmable 10 points curve for the temperature coefficient. Switching between a single TempCo and the curve can be done at any time in seconds. GCT20K-MB conductivity transmitter has been released. It is field programmable, with RS485 MODBUS RTU, high isolation, high accuracy, flexibility and reliability. GCT20K conductivity transmitter has been released. It is field programmable, with an isolated loop power 4-20 mA output, high accuracy, flexibility and reliability. Universal input power supplies GPS122D, GPS123D and GPS125D power supplies have been released. They have a second isolated output providing 24 VDC / 42 mA. It can power the isolated analog outputs of our flow computers, loop power devices or just other devices that need to be isolated. Flow Computers for Liquids GFC100/200 series Flow Computers GFC301 wall mount IP65 (NEMA-4) dual channel flow computer for liquids, gases and steam is released. Batch functionality has been added to each channel. The analog output (when 4-20 mA loop power) works from 7.0 V allowing up to 250 ohm load on a car / truck battery. All options for the analog output have a lot higher accuracy and resolution. All GFC100/200 series flow computers now have an ''E'' version. All the same features but in one inch wider enclosure - more space for the wires. A new GFC110A-B flow computer has been released. Accepts a biderectional flow sensor and displays flow rate A, flow rate B and total A-B. GFC116 low power flow computer / totalizer has been released. It has a simplified menu, separate volume units for rate and total and no batch, limit, datalog or alarm options. KFACTOR unit is not fixed but in the total units programmed. SETP is in pulses per total unit. GFC106 micro power flow computer / totalizer has been released. It has a simplified menu, separate volume units for rate and total and no batch, limit, datalog or alarm options. KFACTOR unit is not fixed but in the total units programmed. SETP is in pulses per total unit. New universal input power supplies New 10W and 20W universal input power supplies GPS123, released: 10W, universal input 90 - 264 VAC, highly isolated and protected output 24VDC/0.42A with low ripple. Board assembly or mounted in a weather proof enclosure ... GPS125, released: 20W, universal input 90 - 264 VAC, highly isolated and protected output 24VDC/0.84A with low ripple. Board assembly or mounted in a weather proof enclosure ... Analog outputs All 4-20 mA analog outputs of our devices will work with voltage down to 6VDC. Same high accuracy, on even higher loads (up to 1600 ohm). Great when powering from a car battery .... Software New version of ''GRD Master'' software coming soon to cover all new versions of GRD100 series remote displays and add more functions. New ''GTT Master'' and ''GMAG Master'' software will greatly help for quick field programming, monitoring and control of our field programmable temperature transmitters and magmeters ....